Radio Frequency Identification

Radio Frequency Identification (RFID) is an automatic identification method, relying on storing and remotely retrieving data using devices called RFID tags or transponders. An RFID tag is an object that can be attached to or incorporated into a product, animal, or person for the purpose of identification using radio waves. Chip-based RFID tags contain silicon chips and antennas. Passive tags require no internal power source, whereas active tags require a power source.

Types of RFID tags

RFID cards are also known as "proximity", "proxy" or "contactless cards" and come in three general varieties: passive, semi-passive (also known as semi-active), or active.

Passive RFID tags have no internal power supply. The minute electrical current induced in the antenna by the incoming radio frequency signal provides just enough power for the CMOS integrated circuit in the tag to power up and transmit a response. Most passive tags signal by backscattering the carrier signal from the reader. This means that the antenna has to be designed to both collect power from the incoming signal and also to transmit the outbound backscatter signal. The response of a passive RFID tag is not necessarily just an ID number; the tag chip can contain non-volatile EEPROM for storing data.

The lack of an onboard power supply means that the device can be quite small: commercially available products exist that can be embedded in a sticker, or under the skin. As of 2006, the smallest such devices measured 0.15 mm × 0.15 mm, and are thinner than a sheet of paper (7.5 micrometers). [2] The lowest cost EPC RFID tags, which are the standard chosen by Wal-Mart, DOD, Target, Tesco in the UK and Metro AG in Germany, are available today at a price of 5 cents each. The addition of the antenna creates a tag that varies from the size of a postage stamp to the size of a post card. Passive tags have practical read distances ranging from about 10 cm (4 in.) (ISO 14443) up to a few meters (EPC and ISO 18000-6) depending on the chosen radio frequency and antenna design/size. Due to their simplicity in design they are also suitable for manufacture with a printing process for the antennas.

Non-silicon tags made from polymer semiconductors are currently being developed by several companies globally. Simple laboratory printed polymer tags operating at 13.56 MHz were demonstrated in 2005 by both PolyIC (Germany) and Philips (The Netherlands). If successfully commercialized, polymer tags will be roll printable, like a magazine, and much less expensive than silicon-based tags. The end game for most item level tagging over the next few decades may be that RFID tags will be wholly printed - the same way a barcode is today - and be virtually free, like a barcode. However, substantial technical and economic hurdles must be surmounted to accomplish such an end: hundreds of billions of dollars have been invested over the last three decades in silicon processing, resulting in a per-feature cost which is actually less than that of conventional printing.

Unlike passive RFID tags, active RFID tags have their own internal power source which is used to power any ICs that generate the outgoing signal. Active tags are typically much more reliable (e.g. fewer errors) than passive tags due to the ability for active tags to conduct a "session" with a reader. Active tags, due to their onboard power supply, also transmit at higher power levels than passive tags, allowing them to be more effective in "RF challenged" environments like water (including humans/cattle, which are mostly water), metal (shipping containers, vehicles), or at longer distances. Many active tags have practical ranges of hundreds of meters, and a battery life of up to 10 years. Some active RFID tags include sensors such as temperature logging which have been used in concrete maturity monitoring or to monitor the temperature of perishable goods. Other sensors that have been married with active RFID include humidity, shock/vibration, light, radiation, temperature and atmospherics like ethylene. Active tags typically have much longer range (approximately 300 feet) and larger memories than passive tags, as well as the ability to store additional information sent by the transceiver. The United States Department of Defense has successfully used active tags to reduce Logistics costs and improve Supply Chain visibility for more than 15 years. At present, the smallest active tags are about the size of a coin and sell for a few dollars.

An RFID system may consist of several components: tags/transponders, tag readers, antenna, middleware/application software.

The purpose of an RFID system is to enable data to be transmitted by a mobile device, called a tag, which is read by an RFID reader and processed according to the needs of a particular application. The data transmitted by the tag may provide identification or location information, or specifics about the product tagged, such as price, color, date of purchase, etc. The use of RFID in tracking and access applications first appeared in 1932, to identify aircraft as friendly or unfriendly ("identify friend or foe" (IFF)). RFID quickly gained attention because of its ability to track moving objects. As the Technology is refined, more Pervasive and possibly invasive uses for RFID tags are in the works.

In a typical RFID system, individual objects are equipped with a small, inexpensive tag. The tag contains a transponder with a digital memory chip that is given a unique electronic product code. The interrogator, an antenna packaged with a transceiver and decoder, emits a signal activating the RFID tag so it can read and write data to it. When an RFID tag passes through the electromagnetic zone, it detects the reader's activation signal. The reader decodes the data encoded in the tag's integrated circuit (silicon chip) and the data is passed to the host computer. The application software on the host processes the data, and may perform various filtering operations to reduce the numerous often redundant reads of the same tag to a smaller and more useful data set.

Take the example of books in a library. Security gates can detect whether or not a book has been properly checked out of the library. When users return items, the security bit is re-set and the item record in the Integrated library system is automatically updated. In some RFID solutions, a return receipt can be generated. At this point, materials can be roughly sorted into bins by the return equipment. Inventory wands provide a finer detail of sorting. This tool can be used to put books into shelf-ready order.

Source: Wikipedia RFID